Active TopicsActive Topics  Display List of Forum MembersMemberlist  Search The ForumSearch  HelpHelp
  RegisterRegister  LoginLogin
PowerHome Bug Reports
 PowerHome Messageboard : PowerHome Bug Reports
Subject Topic: Event log shows no incoming Insteon Post ReplyPost New Topic
Author
Message << Prev Topic | Next Topic >>
FuseWerx
Newbie
Newbie


Joined: March 28 2006
Online Status: Offline
Posts: 4
Posted: March 28 2006 at 10:37 | IP Logged Quote FuseWerx
I have successfully discovered a number of KPLs and SLs, and created links using PH between the SLs and the PLC. (phew, lots of TLAs in there -- three letter acronyms)

Event log does not show ANY "incoming insteon" at all. None. Nada. Zip. I can discover links, I can send Insteon commands, it's picking up X10 signals and showing them as incoming, but Insteon? Uh, no.

Any ideas/help?
Back to Top View FuseWerx's Profile Search for other posts by FuseWerx
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
Posted: March 28 2006 at 11:01 | IP Logged Quote TonyNo
I am in the same boat. Hopefully, Dave can come up with some things to try.
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
FuseWerx
Newbie
Newbie


Joined: March 28 2006
Online Status: Offline
Posts: 4
Posted: March 28 2006 at 11:13 | IP Logged Quote FuseWerx
FYI: The SDM log shows incoming raw Insteon commands, so the problem doesn't appear to be SDM...
Back to Top View FuseWerx's Profile Search for other posts by FuseWerx
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
Posted: March 28 2006 at 11:28 | IP Logged Quote TonyNo
Ditto. Same here.
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
FuseWerx
Newbie
Newbie


Joined: March 28 2006
Online Status: Offline
Posts: 4
Posted: March 30 2006 at 23:41 | IP Logged Quote FuseWerx
*bump*

Sent a link to this thread to support, too. No news is bad news when it's needed pre-sales.

Shall I move on to something else?
Back to Top View FuseWerx's Profile Search for other posts by FuseWerx
 
ColinB
Newbie
Newbie


Joined: March 29 2006
Online Status: Offline
Posts: 8
Posted: March 31 2006 at 07:34 | IP Logged Quote ColinB
I had to turn on logging of Insteon messages in the Setup-Logs section of the PowerHome Explorer.
Back to Top View ColinB's Profile Search for other posts by ColinB
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
Posted: March 31 2006 at 08:06 | IP Logged Quote TonyNo
EHX is happening, so, I bet Dave is busy with that. He'll respond soon.
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
ColinB
Newbie
Newbie


Joined: March 29 2006
Online Status: Offline
Posts: 8
Posted: March 31 2006 at 08:27 | IP Logged Quote ColinB
Just to clarify my above post. I wasn't seeing any Insteon messages either when I initially installed Powerhome. When I looked at the Log Setup screen the Insteon In and Out options weren't checked 'on'. Selecting them fixed the problem. Maybe the new version has a different default setting than the previous one?
Back to Top View ColinB's Profile Search for other posts by ColinB
 
FuseWerx
Newbie
Newbie


Joined: March 28 2006
Online Status: Offline
Posts: 4
Posted: March 31 2006 at 09:44 | IP Logged Quote FuseWerx
ColinB: That did it. Now my test trigger works. It didn't before; perhaps when inbound Insteon logging is off, triggers don't work on inbound Insteon commands?
Back to Top View FuseWerx's Profile Search for other posts by FuseWerx
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
Posted: March 31 2006 at 10:10 | IP Logged Quote TonyNo
Hmm. Logging should not be required for triggers. Could be a bug. I just enabled Insteon In; we'll see what happens.
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
TonyNo
Moderator Group
Moderator Group
Avatar

Joined: December 05 2001
Location: United States
Online Status: Offline
Posts: 2889
Posted: March 31 2006 at 19:02 | IP Logged Quote TonyNo
Bingo! Great catch, ColinB!
Back to Top View TonyNo's Profile Search for other posts by TonyNo Visit TonyNo's Homepage
 
dhoward
Admin Group
Admin Group
Avatar

Joined: June 29 2001
Location: United States
Online Status: Offline
Posts: 4447
Posted: April 04 2006 at 18:57 | IP Logged Quote dhoward
Great detective work guys! FuseWerx, sorry to take so long in responding. Was at the EHExpo and had absolutely no time to check the board or email.

The show was definately interesting. Testing PowerHome for 8 hours a day for 3 days doing nothing but linking, unlinking, etc. really was a torture test (for both me and PowerHome). Ive uncovered some additional bugs to the one discovered in this thread and will be releasing a new version shortly.

Appreciate your patience and you guys catching this bug for me.

Dave.
Back to Top View dhoward's Profile Search for other posts by dhoward Visit dhoward's Homepage
 

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

  Post ReplyPost New Topic
Printable version Printable version

Forum Jump
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum